iheir test霉菌测试笔是用于材料或成品测量是否感染霉菌,10分钟就可以判断结果,有别于其他的测试方法需要28天才有结果,具有快准狠的优势。
步:拔开棉签试管。
第二步:用棉签轻微擦拭受检测产品表面,采集霉菌。取样时,必须收集足够的霉菌材料。
第三步:将棉签放回测试管,用力向下按压手柄,直到棉签卡入下方测试液中,迅速摇晃5秒,
然后等待大约 10 分钟左右,如果溶液变绿,则代表您的产品表面无霉菌,是干净的!如果溶剂变
紫,则代表您的产品表面存在大量霉菌生长,需做适当的防霉处理。
因为这个溶液会寻找霉菌中特定的蛋白质和碳水化合物的存在,使其产生“假阳性”的效果,
使其变色。但是需要注意的是,某些物质如食品,血液可能会产生“假阳性”结果,因此在测试前
需保证测试材料表面没附着食品,血液等物质。溶剂在使用过后,终会因为收到细菌的侵袭而回
逐渐变紫(24小时内)。
3.insert the swab back into the tube, firmly press
down on the handle until the swab snaps into the solution
chamber. shake rapidly for at least 5 seconds. wait up to 10 minutes for results. if it’s
green it’s clean!
because this test looks for the presence of specific proteins and carbohydrates it is
subject to false negative and positive results. certain substances such as food, blood and
untreated wood may yield a false positive result. eventually the solution will turn
purple(usually between 1 hour and 24 hour即时霉菌测试笔原理
in the unlikely event of contact with test reagents please note the following: in case of
contact with eyes, immediately flush eyes with plenty of water for at least 15 min . in case
of contact with skin, flush immediately with plenty of water. if case of contact with skin,
flush immediately with plenty of water . if irritation persists get medical attention. if
swallowed, wash out mouth with water and seek medical advice.
iheir mold test kit 即时霉菌测试笔是广州艾浩尔防霉抗菌科技有限公司2015年尾
新研发用于测试材料表面霉菌用测试笔,可检测正常环境下材料表面附着霉菌数量。
测试原理:
通常霉菌均是带负电荷,会主动吸附带正电荷的物质,我们的技术人员通过利用负电荷
自动吸附正电荷的特性,研发出一种新型的特殊溶剂,我们称其为“霉菌测试溶剂”。霉菌测
试溶液为正电荷,会对自动吸附过来的霉菌产生“假阳性”的现象,然后产生化学反应,使溶
剂颜色改变。该化学反应会在5~10分钟内作用于溶剂本身,跟传统测试方式相比,本测试笔
具有使用方便、准确、肉眼可见等优点,想要知道产品表面有没有霉菌,一擦就知道。
艾浩尔业务部何先生:2816247964